Skip to content

Home
Printers

Filament printers

BIG-60 In stock
600 × 600 × 660 mm
From 5,700 USD
Learn more

BIG-120X In stock
1,200 × 600 × 640 mm
From 8,300 USD
Learn more

BIG-120Z In stock
600 × 600 × 1,200 mm
From 8,300 USD
Learn more

BIG-Meter In stock
980 × 1,000 × 1,000 mm
From 15,300 USD
Learn more

BIG-180X In stock
1,800 × 600 × 660 mm
From 17,300 USD
Learn more

Everest In stock
970 × 1,030 × 2,000 mm
From 27,000 USD
Learn more

Pellet & filament printers

MAMA-1000
1,000 × 1,000 × 1,000 mm
Contact for pricing
Learn more

MAMA-1700
1,700 × 1,000 × 1,000 mm
Contact for pricing
Learn more

MAMA XL-3000
3,000 × 1,000 × 1,000 mm
Contact for pricing
Learn more

Compare tech specs See use cases Add-ons Request a quotation
Add ons
Tech Specs
Technical specifications

Compare modelsSix BIG machines, side by side GEN5 NewWhat changed in Generation 5 PlatformWhat is inside every BIG printer Print headsFour Griffin options, one mount IDEXTwo independent print heads Add-onsConfigure the machine to the job MaterialsOpen system, any 1.75 mm filament MAMA pellet lineIndustrial pellet extrusion Security & compliance NewAir-gapped and restricted sites

Six machines. One platform. Pick the volume.

Build volumes from 600 × 600 × 660 to 1,800 × 600 × 660 mm

GEN5 base prices from 5,700 USD, with Configure links per model

Switch to millimetres or inches, or filter to the differences only

Open the comparison table →

What's new in Modix GEN5

Duet 3 6HC controller with distributed CAN-FD expansion

Smart tool board on the print head, new touchscreen interface

Backward compatible: GEN5 parts fit earlier Modix machines

See the seven GEN5 changes →

What is inside every BIG printer

HIWIN linear rails, four 12 mm ball screws on Z, Gates GT2 belts

Automatic bed tilt, mesh leveling, gantry alignment and Z offset

Eight panels: electronics, motion, calibration, bed, chassis, power, software, safety

Open the platform spec sheet →

One mount. Four print head options.

Griffin Ultra for the biggest parts, plus Standard, High-Resolution and High-Flow

Layer heights 0.05 to 1.2 mm, hotend and nozzle dependent

Same mount on every model, so a head swap is not a rebuild

Compare the four heads →

Two independent heads. Clean dual-material prints.

Water-soluble supports and interface layers on the second head

Automatic filament changer for long unattended jobs

IDEX calibration tool measures the XYZ offset, no test prints

See the IDEX kit →

Configure the machine to the job.

Enclosure, active air filter, inline filament dryer, Smart PDU

Z rails, casters, spool shelf, spare-parts kits, hardened nozzles

Every add-on is priced live in the configurator

Browse the add-ons →

Open material system. No lock-in.

Any 1.75 mm filament, with tested Modix print profiles

Three tiers: Easy (PLA, PETG), Intermediate (PP, PA, TPU), Advanced (ABS, ASA, PC)

Carbon and glass filled print with the hardened-steel nozzle pack

Open the material list →

Industrial pellet extrusion, up to 3 kg per hour.

MAMA-1000, MAMA-1700 and MAMA XL-3000, three configurations each

Pellet and filament in one machine, granulate at commodity prices

Quoted per project: dryer, mixer, air filter, spares and feedstock

Open the MAMA table →

No radio required

Built to run inside a closed network.

Runs fully offline: no cloud account, no internet connection needed

Ethernet as standard and a removable Wi-Fi dongle; closed access-point mode on request

Off-the-shelf Duet 3 board and open-source RepRapFirmware, both replaceable by you

Read the security notes →

All printers Configure your printer See use cases Talk to an engineer Request a quotation
Use Cases
Support
News
About
Contact