Tech Spec

What’s new in Version 2- check here

General Information

  • Printing Technology – FFF (Filament Filament Fabrication)
  • Number of print heads – single or dual (optional)
  • Delivery – Self assembly kit.

Dimensions

  • Big60 build volume  – 610 X 610 X 610 mm
  • 120X build volume –  1200 X 610 X 610 mm
  • Big60 machine size- 900 X 926 X 1170 mm (W X D X H)
  • Big120 machine size- 1520X 926 X 1221 mm (W X D X H)

Construction

  • Solid 40X40 T-slot aluminum profiles
  • Powder coated laser cut aluminum brackets and joints
  • Closed enclosure made of acrylic (optional)

Motion System

  • Hiwin MGn12H linear guides rails
  • Z ball nut screws for Z axis 
  • 9mm width Gates GT2 timing belt, fiber glass reinforced.
  • Z motors: 3 X belt geared 40mm Nema 17.
  • X & Y motors: 60mm Nema 17
  • Position accuracy: X 5 Micron, Y 10 Micron,  Z 0.5 Micron.
  • Print speed – Normal 60-80 mm/2, Draft 100-150 mm/sec

Hot End

  • E3D V6 volcano high flow heat block.
  • 1.75 mm filament diameter.
  • 0.4, 0.6 & 0.8 mm brass Volcano nozzles.
  • Smaller nozzle diameters are available for the standard V6
  • Heater cartridge is  24V 40W
  • Part cooling fan – 5015 blower fan

Extruder

  • E3D Titan extruder for both primary and secondary extruder.
  • Configuration: Main – direct drive, secondary – Bowden.
  • Secondary print head is designed for support material.
  • Extruder drive gear ratio 3:1 for power and accuracy.
  • Nema17 40mm for high power extrusion.
  • Adjustable idler tension

Print Bed

  • 6.35mm thick, Alcoa Mic6 milled cast aluminum plate.
  • AC powered bed heater 1600Watt.
  • Dual heating zones. Inner 200X200mm size for small objects.
  • Max temperature – 120c
  • Print surface – PEI film with adhesive sheet.

Auto Bed leveling

  • Inductive sensor, BL touch optional.
  • Marlin firmware unified bed leveling algorithm.
  • Probing of bed shape is kept in controller memory.
  • Big60 – 100 points, 120X – 150 points.
  • Online editor for easy manual map editing.

Software

  • Open source Marlin firmware. The leading firmware for 3D printing allowing numerous of configurations and the widest comparability to both software and hardware.
  • Firmware is installed on an Arduino based controller from Makerbase, MKS Gen 1.4.
  • You can choose from any available slicer and 3d printer controller including: Slic3r, Cura, Printerface and Simplified3d. We provide printer profiles.

Power

  • Supporting both 110V and 230V
  • Enclosed Power Supply – Meanwell 24V 280W
    • Protections: Short / Overload / Over voltage / Over temp.
    • No load power consumption<0.5W
    • LED indicator for power on
    • Aviation grade switches and connectors
  • Heat Bed AC powered heater  1600Watt
  • Autonic PID controller & Solid state relay

Control

  • Stand alone operation: SD Card
  • From PC- USB cable
  • Optional Wifi control via Octoprint

Filament

Our printing head supports almost any existing filament including : PLA, ABS, PLA composites (Carbon fiber, Wood, Copper, Brass, Magnetic ), PHA, PVA , Hips, Nylon, TPE & TPU (FleX) Co-Polyester, PETG…

Open Filament  – you can use any filament from any vendor.

Filament Run-Out Sensor – The filament run-out detection sensor will pause the print job when the filament is finished.

Send data sheet & more info: